TotalBoat Outdrive AF (Non-Aerosol)
Antifouling for outdrives and props
Dual biocide controls hard and soft fouling
Smooth, durable, polishing finish
Available in Black
TotalBoat Outdrive AF is a full-season, copper-free ablative antifouling paint for underwater metals. Safe for aluminum and other metals because it won't cause galvanic corrosion. Use on props, drives, keels, trim tabs, through-hulls, bow thrusters, shafts, and struts.
Product Overview
-
Cleaner/Surface Preparation Solvents:
- TotalBoat Dewaxer & Surface Prep
- TotalBoat Brushing Thinner 100
- TotalBoat Spray Thinner 101
- Acetone (bare substrates only)
- Cleanup Solvents:
-
Thinner/Reducer Solvents:
- TotalBoat Brushing Thinner 100, for brushing and rolling applications
- TotalBoat Spray Thinner 101, for spraying and cool weather brushing/rolling applications
- Primer/Precoat: TotalBoat TotalProtect (iron/steel), TotalBoat Aluminum Boat Barrier Coat (aluminum), TotalBoat Aluminum Boat Etch Wash (aluminum)
- Acceptable Substrates: Fiberglass, wood, steel/iron, aluminum, and properly prepared previously painted substrates
- Available Color: Black
Surface Preparation
- When using solvent wipes, change rags frequently to remove all wax and contaminants.
- Allow surfaces to dry completely between steps.
- Mask off areas not to be painted.
Aluminum
- Remove debris and rust.
- Sandblast or grind to bare metal (2–3 mil profile).
- Clean using TotalBoat Dewaxer & Surface Prep.
- Etch using TotalBoat Aluminum Boat Etch Wash.
- Apply TotalBoat Aluminum Boat Barrier Coat.
Bare Steel or Iron
- Remove rust and debris.
- Sandblast or grind to bare metal.
- Clean and apply TotalBoat TotalProtect.
Previously Painted Surfaces
- Apply only over compatible coatings.
- Sand and clean using TotalBoat Brushing Thinner 100 or TotalBoat Dewaxer & Surface Prep.
Application Over Barrier Coats
Thumbprint-Tacky Method
- Apply when coating is tacky but does not transfer to finger.
Sanding Method
- Wait 24 hours, sand with 80-grit, clean thoroughly, and apply.
Application Conditions
- 50–90°F, under 90% humidity
- Avoid direct sunlight and moisture
Application Methods
- Apply 1–2 coats per season
- Extra coats recommended in high-wear areas
- Apply at 2.5–3 mils wet film thickness
Dry Time to Launch
- 2 hours @ 90°F
- 4 hours @ 70°F
- 8 hours @ 50°F
Brushing/Rolling Instructions
- Thinning not usually required
- If needed, thin 5–10% with TotalBoat Brushing Thinner 100
- Use 3/16" rollers only
Spraying Instructions
- Thin up to 5% with TotalBoat Spray Thinner 101
- Recommended nozzle: 1.8–2mm
Maintenance
Inspect regularly. Do not scrub for the first six months. Clean every three months thereafter.
Warning
RAGS, STEEL WOOL, OR WASTE SOAKED WITH THIS PRODUCT MAY SPONTANEOUSLY CATCH FIRE IF DISCARDED IMPROPERLY.
Personal Safety
Use proper PPE and ensure adequate ventilation.
Application Data
| Application Method | Brush, Roll, Spray |
| Number of Coats | 1-2 |
| Thinner/Reducer | TotalBoat Brushing Thinner 100, TotalBoat Spray Thinner 101 |
| Coverage | 500 sq ft/gal |
| Film Thickness | 1.5 mils dry (2.7 mils WFT) |
| Colors | Black |
| Sizes | Quart |
Physical Data
| Flash Point | 105°F |
| Waters | Salt & Fresh |
| Base | Solvent |
| Finish | Eggshell |
| Biocides | Zinc Pyrithione 4.8%, Tralopyril 6.0% |
| VOC | < 330 g/L |