TotalBoat Krypton

Uses copper-free technology

Dual biocide control hard & soft fouling

Clean, bright colors

Available in Black, Blue, Green, Red, White

TotalBoat Krypton is an environmentally friendly antifouling bottom paint that contains the most effective concentration of copper-free biocide available, combined with slime-fighting zinc for superior antifouling protection against barnacles, mussels, slime, and weeds. Use on properly prepared aluminum, fiberglass, wood, or steel boats in fresh and salt water. Krypton is also ideal for outdrives, trim tabs, and other underwater metals.

Product Overview

• Cleaner/Surface Preparation Solvents:
  • TotalBoat Dewaxer & Surface Prep
  • TotalBoat Brushing Thinner 100
  • TotalBoat Spray Thinner 101
  • Acetone (bare substrates only, but specifically recommended for use on oily hardwoods or bare white oak)
• Cleanup Solvents:
  • TotalBoat Dewaxer & Surface Prep
  • TotalBoat Brushing Thinner 100
  • TotalBoat Spray Thinner 101
• Thinner/Reducer Solvents:
  • TotalBoat Brushing Thinner 100, for brushing and rolling applications
  • TotalBoat Spray Thinner 101, for spraying and cool weather brushing/rolling applications
• Primer/Precoat: TotalBoat TotalProtect, TotalBoat Aluminum Boat Barrier Coat
• Acceptable Substrates: Fiberglass, wood, steel/iron, aluminum, and properly prepared previously painted substrates
• Available Colors: Black, Blue, Green, Red, White

Surface Preparation

Bare Fiberglass or Gelcoat

• All bare fiberglass substrates need to be fully cured for at least 5-7 days prior to any surface preparation.
• The surface must be properly dewaxed, or amine blush must be removed prior to any further surface preparation.
• Wash the surface with warm water and a mild soap. Dry the surface completely.
• Dewax the surface very thoroughly using TotalBoat Dewaxer & Surface Prep and clean cotton rags. DO NOT use synthetic rags. Change out rags as needed to ensure all wax is removed.
• Allow the surface to dry completely.
• Mask off any areas that are not to be painted with Krypton antifouling paint.
• Sand the surface with 80-grit sandpaper to a dull, frosty finish.
• Remove sanding residue with a clean rag dampened with Dewaxer & Surface Prep, then wipe dry.
• Allow the surface to dry completely before applying Krypton.

Barrier Coat Application:

• Applying a barrier coat such as TotalBoat TotalProtect is strongly recommended to prevent osmotic blisters.
• Apply as directed before applying Krypton antifouling paint.

Bare Wood

• Wood must be clean, dry, and free of contaminants.
• Mask off areas not to be painted.
• Fill seams as needed.
• Sand smooth with 80-grit sandpaper.
• Clean with TotalBoat Brushing Thinner 100 and dry thoroughly.
• Apply 2 coats of Krypton.

Previously Painted Surfaces

• Apply only to compatible antifouling paints in good condition.
• Sand with 80-grit and clean using TotalBoat Brushing Thinner 100 or TotalBoat Dewaxer & Surface Prep.
• Remove failing coatings completely before repainting.

Bare Steel or Iron

• Remove rust and debris.
• Sandblast or grind to bare metal.
• Clean and apply TotalBoat TotalProtect.
• Apply Krypton.

Aluminum

• Prepare surface as above.
• Apply TotalBoat Aluminum Boat Barrier Coat within 1 hour.

Application Conditions

• 50–90°F, under 90% humidity
• Avoid direct sunlight and high humidity conditions

Application Methods

• Apply 1–2 coats per season
• Apply additional coats in high-wear areas
• Apply at 2.5–3 mils wet film thickness

Dry Time to Launch

• 2 hours @ 90°F
• 4 hours @ 70°F
• 8 hours @ 50°F

Maintenance

Check regularly for buildup. Do not scrub for the first six months. Clean every three months thereafter.

Warning

RAGS, STEEL WOOL, OR WASTE SOAKED WITH THIS PRODUCT MAY SPONTANEOUSLY CATCH FIRE IF DISCARDED IMPROPERLY.

Personal Safety

Use proper PPE and ensure adequate ventilation when applying.

Application Data

Physical Data